Home Laser Shutters SRS SR470 Optical Laser Shutter System

SRS SR470 Optical Laser Shutter System

Availability: In stock


Product Code:
19991
Manufacturer: Stanford Research Systems
Special Price £1,988.50 £2,386.20 Regular Price £2,460.00
  • Ultra-low vibration shutter head
  • True mechanical laser beam blocking
  • >10 M cycle lifetime
  • Microprocessor controlled timing
  • DC to 125 Hz (any duty cycle)
  • Easy to align 3 mm aperture
  • GPIB, RS-232, Ethernet interfaces

More info and finance questions

Lambda Exclusive Promotion:
Additional 12 months warranty for free (2 years total) via our UK Service Centre.

Introducing two new optical shutter systems from Stanford Research Systems — the SRS SR470 Laser Shutter Controller and SRS SR474 Four-Channel Laser Shutter Driver. These shutter systems are designed specifically to minimize vibration on your optical table.

Shutter Head
Unlike conventional solenoid based shutters, the SR475 shutter head contains a closed-loop DSP control system that precisely guides the shutter blade between open and closed positions, never encountering physical stops. Vibration and mechanical noise are kept to a minimum, leaving your optical table disturbance-free.

The shutter blade is mounted between sapphire jewel bearings that minimise friction and result in a head lifetime in excess of 10 M cycles — orders of magnitude more than is typically found in shutter heads.

The 3mm clear aperture is designed for easy alignment and is large enough to be used with common light sources. Typical rise and fall times are under 500 µs, and repetition rates from DC to 125 Hz can be used. Unlike other shutters, the SRS shutter is not duty cycle limited — you can run any duty cycle you choose.

SR470 Controller
The SR470 Shutter Controller allows you to generate timing signals for the shutter head. You have complete control of the exposure time, which can be set between 4 ms and 10,000 s with 0.1 ms resolution. Pre- and post-exposure delays can also be configured. A bright green 8-digit LED display shows the current parameter in seconds or hertz, and timing is accurate to 100 ppm.

A variety of trigger modes are provided — internal, external, front panel, and continuous — giving you the flexibility to handle just about any application. Triggered bursts from milliseconds to months can also be generated, placing the SR470 in a class of its own.

In addition to triggered sequences, the SR470 can also act as a driver to actuate the shutter head from your own timing signals. You can also manually control the shutter from the front panel.

Remote operation is supported with GPIB, RS-232 and Ethernet computer interfaces. All instrument functions can be controlled and read over any of the interfaces. Up to nine complete instrument configurations can be saved in non-volatile RAM and recalled at any time. Shutter faults are automatically detected and reported with audible and electronic (TTL) alarms.

SR474 Four-Channel Driver
The SR474 Four-Channel Driver interfaces with up to four shutter heads. Rear-panel TTL level inputs are provided for your external timing signals. Each of the four channels can be set for normally open or normally closed operation.

Each channel has a front-panel State button which allows you to manually change the shutter state. The channel Source buttons set each channel to manual, external TTL or remote state control. Each channel also has an Align button that drives its shutter head at a 1 Hz rate making laser alignment simple. The Global Control section of the front-panel allow you to set or reset all channels to their “normal” states.

As with the SR470, remote operation is supported with GPIB, RS-232 and Ethernet computer interfaces. All instrument functions can be controlled and read over any of the interfaces. Shutter faults are automatically detected and result in audible, visible and electronic alarms.

About the Shutter Head
Unlike conventional designs, the SR475 Shutter Head can be mounted on your optical table in any orientation. This gives you complete flexibility to route the mating cable out of the way of your experiment.

The 3 mm aperture is positioned very close to the chassis edge, making the SR475 ideal for chopping one of two parallel beams separated by less than a centimeter. It also allows you to operate your lasers very close to the plane of your optical table top.

The SR475’s small size makes it ideal in tight quarters, and with a precision guided blade, shutter vibration is essentially eliminated.

 

 

 

Mechanical  
Shutter blade BeCu alloy, black oxide finish
Clear aperture 0.120 in. min. diameter
Exposure rise/fall time  
Insertion delay jitter 10 µs rms typ. (measured at 10 Hz rep rate)
 
Bearing Sapphire jewel bearing
Blade position Closed-loop PID controlled
Opening/closing bounce None allowed
 
Operating temperature 0 °C to 35 °C
 
Mounting Any orientation
   
General  
Max. cable length 3 m
Weight 1 lbs.
Dimensions 2.25" × 1.60 " × 1.00" (WHL)
Power 4.5 VDC @ 250 mA, 12 VDC @ 1.25 A
Warranty
 
One year parts and labor on defects in materials and workmanship, or 10 M cycles, whichever comes first.
Write Your Own Review
You're reviewing:SRS SR470 Optical Laser Shutter System
Your Rating
PhotoProduct SKU
SRS SR474 4 Channel Laser Shutter DriverSRS SR474 4 Channel Laser Shutter Driver- >
SRS SR475 Laser Shutter Head 100 HzSRS SR475 Laser Shutter Head 100 Hz- >