Home Distribution Amplifiers SRS FS730/3 CMOS Logic Distribution Amplifier

SRS FS730/3 CMOS Logic Distribution Amplifier

Product Code:
21623
Manufacturer: Stanford Research Systems
  • High input impedance with hysteresis
  • High current outputs
  • Fast transition times
  • Small insertion delay
  • Low channel-to-channel timing skew

More info and finance questions

Request a Quote

Lambda Exclusive Promotion:
Additional 12 months warranty for free (2 years total) via our UK Service Centre.

The Stanford Research Systems FS730/3 Series Distribution Amplifiers are used to distribute CMOS level logic pulses. Each amplifier has one input and seven outputs, all on BNC connectors. All inputs and outputs are logic levels.

The Schmitt trigger input has a switching threshold of +1.3 VDC with 0.35 V of hysteresis. The input impedance is 1 kΩ.

CMOS Distribution Amplifier - Offset 10 MHz sine input (500mV/div), logic output (2V/div into 50ohm) and logic output (2V/div, unterminated and showing small reflection artifacts with 1m cable between output and oscilloscope.) 

Each output has a 50 Ω source impedance with logic levels of 0 VDC and 5.0 VDC. The 50 Ω source impedance will reverse terminate reflected pulses when driving unterminated lines. High impedance loads will be driven to 5 V and 50 Ω loads will be driven to 2.5 VDC. All of the outputs are driven by separate drivers to provide high isolation. The outputs have fast transition times and very low overshoot. The polarity of each output may be configured with a jumper inside the unit: installing the polarity jumper inverts the corresponding output. As shipped, the outputs are non-inverting.

The unit has two indicator LEDs. The “power” LED indicates that the unit has ac power. The “signal” LED will flash for 100ms on each rising or falling edge seen at the input.

Configuration

The SRS FS73x series of products can be configured as half-width, 1U, benchtop instruments (FS730), or in full-width, 1U, 19" rack-mount enclosures (FS735).

The FS730/3 model provides 7 output BNC connectors on the front panel, and can be rack mounted with an optional rack mount kit.

The FS735/3/3 model provides 14 output BNC connectors on the rear panel, with status indicators on the front panel. Several types of distribution amplifiers are available as listed below. Different types may be combined within the FS735 chassis.

   

 

Input  
Impedance 1 kΩ
Threshold (L-H) 1.50 Vdc
Threshold (H-L) 1.15 Vdc
Transition time no restriction
Frequency DC-50 MHz
Pulse width >5 ns
   
Output  
Impedance 50 Ω ±5 %
Levels (high-Z load) 0 V & 5 V
Levels (50 Ω load) 0 V & 2.5 V
Rise time <1.5 ns="" td="">
Fall time <1.0 ns="" td="">
Jitter <10 ps="" rms="" td="">
Delay 9 ns, typ.
Overshoot <5 td="">
Undershoot <5 td="">
Polarity control internal jumper
   
General  
Power 10 W, 100/120/220/240 VAC, 50/60 Hz
Dimensions 8.3" × 1.5" × 8.0" (WHL)
Warranty One year parts and labor on defects in materials and workmanship
Write Your Own Review
You're reviewing:SRS FS730/3 CMOS Logic Distribution Amplifier
Your Rating
PhotoProduct Price
SRS FS735 Double Width 19 Rack Distribution AmplifierSRS FS735 Double Width 19 Rack Distribution Amplifier >
SRS FS730/2 5 MHz Distribution AmplifierSRS FS730/2 5 MHz Distribution Amplifier >
SRS FS730/1 10 MHz Distribution AmplifierSRS FS730/1 10 MHz Distribution Amplifier >
SRS FS730/4 Broadband 50Ω Distribution AmplifierSRS FS730/4 Broadband 50Ω Distribution Amplifier >
SRS FS730/5 Broadband 75Ω Distribution AmplifierSRS FS730/5 Broadband 75Ω Distribution Amplifier >